TESEQ NNB 52 四線V型阻抗穩定網絡

TESEQ NNB 52 四線V型阻抗穩定網絡

四線V型LISN符合CISPR 16-1-2的要求電流達32A頻率范圍：9 kHz～30 MHz手動和遙控操作大截面接地樁

產品特點：在NNB設備的后部分別有兩個輸入接口鏈接被測件電源。CEE主接口4*32A用于EUT。IEC主接頭為LISN控制線路提供需要的功率，也為內部風扇提供交流電源。

技術參數：適用標準: CISPR 16-1-2, MIL-STD-461D, E頻率范圍: 9 kHz ～ 30 MHz負載 (內置): 10 dBNNB 工作電壓: 100 ～ 120 V / 220 ～ 240 V, 50 ～ 63 HzEUT 工作電壓: max. 400 VEUT 頻率: DC ～ 63 HzEUT 相位檢測功能(LED): >48 VEUT 工作電流: max. 4*32 A線性阻抗: 50 Ω || (50 μH + 5 Ω)額定輸出阻抗: 50 ΩRF 接頭: N 母頭模擬手 / 接頭: 510 Ω + 220 pF / 4 mm 香蕉插頭限幅器: 約136 dBμV typ., 可轉換模擬 PE: 可轉換雙線遙控插頭: KFV 60四線遙控插頭: D-sub 25 針尺寸(W x D x H) 不含安裝配件: 450 mm x 375 mm x 265 mm尺寸 (W x D x H): 480 mm x 485 mm x 275 mm重量: 約23.3 kg ApplicationLine impedance stabilization network (LISN) such as the NNB 52 are used to measure distortion signals on the mains cord of an electrical equipment under test (EUT). The distortion signals are usually generated or picked up inside of the EUT and the mains cord acts as an antenna. European and international EMC regulations define maximum permissible signal levels and frequency bands for such distortion signals. The distortion signal to be measured is available on a coaxial N?connector that is mounted on the front panel of the NNB 52. For the actual measurement of the distortion signals a measuring receiver can be used. The V?network is part of a complex EMC?test setup that also has been standardised in CISPR 16?2?1 (EN 55016?2?1).Power supply and connectorsThe NNB 52 has two separate input connectors for the mains power that are located on the rear of the instrument. The CEE mains socket 4x32 A is used to power the EUT. This IEC mains connector is used to supply the required power for the control circuit of the LISN. It also supplies the AC power for the built in blower. Earth connectionThe construction of the NNB 52 allows a massive connection to the shielded room wall. Left and right of the front are grounding bars. Additional are located a connection bolt and wing screw on the rear of the LISN. Remote control connectionThe NNB 52 has two built?in remote control circuits and can be controlled with EMI receivers from MEB/Schaffner/Teseq or Rohde & SchwarzStandards applied: CISPR 16?1?2, MIL?STD?461D and EFrequency range: 9 kHz to 30 MHzAttenuator (build?in): 10 dBNNB operating voltage: 100 to 120 V / 220 to 240 V, 50 to 63 HzEUT operating voltage: max. 400 VEUT frequency: DC to 63 HzEUT phase detection function (LED): >48 VEUT operating current: max. 4x32 ALine impedance: 50 ? || (50 μH + 5 ?)Nominal output impedance: 50 ?RF connector type: N femaleArtificial hand / connector type: 510 ? + 220 pF / 4 mm bananaLimiter: approx. 136 dBμV typ., switchableArtificial PE: switchableConnector type for two wire remote control: KFV 60Connector type for four wire remote control: D?sub 25 pinsSize (W x D x H) without mounting parts: 450 mm x 375 mm x 265 mmSize (W x D x H): 480 mm x 485 mm x 275 mmWeight: approx. 23.3 kgPart number Description253551 NNB 52 Four?line?V?LISN for 32 A97?253550 NNB 5x?TC Traceable calibration (ISO17025) order only with new device 232080 LE 216 Control cable SCR 35xx / NNB xx243134 LE 234 Control cable SMR 45xx / NNB xx

TESEQ NNB 52 四線V型阻抗穩定網絡

深圳市美佳特科技有限公司（簡稱“美佳特"）成立于2010年，致力于光通訊測試、通用電子測量及5G測試服務。美佳特以“無線溝通，溝通無極限 "企業使命，業務聚焦于精密測試測量儀器的租賃、銷售、維護、計量及測試環境搭建等一站式服務。N2843A Keysight 無源探頭 Keysight 是德

主營產品：示波器主機和模塊、眼圖儀、光譜儀、信號源、頻譜分析儀、網絡分析儀、阻抗分析儀、光通信儀器、誤碼儀、光時域反射儀、可調諧激光源、光功率計、光衰減器等。合作品牌：安捷倫、是德、泰克、安立、愛得萬、安騰、力科、馬可尼（IFR）、R&S、EXFO等。N2843A Keysight 無源探頭 Keysight 是德

主推：Agilent 86100D/C 示波器,keysight M8195A 任意波形發生器,Anritsu MS9740B/A 光譜分析儀,YOKOGAWA AQ6370D/E 光譜分析儀,keysight N1092A/C 采樣示波器,keysight E8257D 模擬信號發生器,keysight E5071C 矢量網絡分析儀